» I Gate :: Placement Papers of Companies

I Gate

Filed under:

iGate

I Gate Placement Question Paper

1. Full form of TTL and CMOS

2. Which is a good conductor (Extrinsic or Intrinsic)

3. What are the different types of capacitors (Electrolytic, dielectric…etc)

4. Select a passive component from the following (four choices were there)

5. Minimum no. of lines required for communication using RS232 (Ans: i think its 2)

6. To convert 1’s complement to 2’s complement and vice versa

7. 7. During which time we use ’size of’ command. (ans: runtime)

8. Out of four choice we have to identify which is a macro.

9. There was one pointer expression related question.

10. To find post fix expression.

11. What type of operating system is unix (ans: pre-emptive,[not sure])
a)pre-emptive b)non-preemptive c)batch

12. Defnition of turing machine

13. Where we use DFD(Data flow design)
a)structural languages b)object oriented languages c)UML d)all of the above

14. Name the error which occurs when we write on a page
a) segment fault b)permission fault c) page fault

15. A question based on the representation of an array in C
An array whose elements are fn pointers which inturn returns a character

Related Plament Papers and Companies

I Gate

I Gate Placement Question Paper Aptitude round: 50 ques in 12 min. i. last month of year ii. opp. of Capture iii. if 1$ is saving in 1 month what was average saving per day. iv. easy english idoms and their meaining and usage You can easily attempt 40 around ques. in 12min. Technical Test: 20 ques in 12 min easy ques on O.S. like * what O.S.

Motorola

Motorola Placement Question Paper Hardware questions 1. Draw the state transition diagram for sequence detector for the sequence 011. if the first bit detected is zero then SCRH should be asserted when the second bit is 1 the SCRH should remain asserted when the third bit is 1 the FOUND should be asserted and the SCRH should be disasserted. No bits should be left. 2. ts=0.5 and Th=0.7 (for the this is the setup time reqd and hold time reqd) buffer has the delay of 1nsec what is the setup time _________ns what is the hold time ___________ns Image no.1,2 3. for Each gate delay time

Motorola Placement Question Papers

Motorola Placement Question Papers Hardware questions 1. Draw the state transition diagram for sequence detector for the sequence 011. if the first bit detected is zero then SCRH should be asserted when the second bit is 1 the SCRH should remain asserted when the third bit is 1 the FOUND should be asserted and the SCRH should be disasserted. No bits should be left. 2. ts=0.5 and Th=0.7 (for the this is the setup time reqd and hold time reqd) buffer has the delay of 1nsec what is the setup time _________ns what is the hold time ___________ns Image no.1 3. for Each gate delay

Tata Elxsi

Tata Elxsi Placement Question Paper TECH QUESTIONS (Electronics & TC) 1. CMRR is given= Differential gain is given= Inputs: +ve end=2v,-ve end=1v of the OP-AMP Find the output voltage? 2. CRO is in X-Y mode.Sinusoidal inputs have 90degrees phase difference between them.

Cisco Placement Question Papers

Cisco Placement Question Papers SECTION 1 -- BASIC DIGITAL SECTION 1. In order to find out stack fault of a three input nand gate how many necessary input vectors are needed ? 2. What is parity generation ? 3. A nand gate becomes ___ gate when used with negative logic ? 4. What is the advantage of cmos over nmos ? 5. What is the advantage of synchronous circuits over asynchronous circuits ? 6. What is the function of ALE in 8085 ? 7. A voice signal sample is stored as one byte. Frequency range is 16 Hz to 20 Hz. What is the memory